在設計超聲波清洗設備時，需要遵循一定的要求和標準，如下。

When designing ultrasonic cleaning equipment, certain requirements and standards shall be followed, as follows.

要求和標準

Safety requirements and standards

一定要做好操作人員的防護工作，并采取一定的防護措施。

The safety protection of operators must be done well and certain safety protection measures must be taken.

可靠性要求和標準

Reliability requirements and standards

1、必須是嚴謹科學的人體工學設計，以保證其工作的可靠性和穩定性。

1. It must be a rigorous and scientific ergonomic design to ensure the reliability and stability of its work.

2、設計必須，技術很成熟，結構很緊湊，測試精度必須很高。

2. The design must be advanced, the technology is mature, the structure is compact, and the test accuracy must be very high.

3、要求電腦性能，配置非常可靠，運行時能快速完成操作。

3. It is required that the computer has good performance, reliable configuration and can complete the operation quickly when running.

3. 可操作性和可維護性的要求和標準

3. requirements and standards for operability and maintainability

1、操作非常簡單易懂，配備顯示屏，操作非常方便。

1. The operation is very simple and easy to understand. Equipped with display =, the operation is very convenient.

2、盡量節約能源，保證維護和使用成本很低，外觀也要求美觀。

2. Save energy as much as possible to ensure low maintenance and use costs and beautiful appearance.

3、維護良好，使用壽命可達10年以上。

3. Good maintenance and service life of more than 10 years.

此外超聲波清洗設備是實驗室中的常用設備，它具有很多優勢，可以不傷害任何工件，清潔范圍廣，清潔的徹底，而且能夠做到綠色，大大提高了實驗室清洗工作效率。

In addition, ultrasonic cleaning equipment is a common equipment in the laboratory. It has many advantages. It can not hurt any workpiece. It has a wide range of cleaning and is thoroughly cleaned. It can be green and environmental protection, and greatly improve the efficiency of laboratory cleaning.

1、接通電源要符合規格要求，確保是接地的。

1. The power supply shall meet the specification requirements to ensure that it is grounded.

2、不能使用燃性清潔劑，以防使用中發生爆炸。

2. Do not use flammable detergent to prevent explosion during use.

3、注入清洗液的時候好是容器容積的四分之三，不要倒的過滿。

3. The volume of the container should be three fourths of the volume when filling the cleaning solution. Do not overfill it.

4、把待清洗工件放入，再倒上清洗液，在插電源，清洗時間要設定好了，再開機。

4. Put the workpiece to be cleaned in, pour the cleaning liquid, plug in the power supply, and start the machine after the cleaning time is set.

5、切勿用重物撞擊清洗缸的缸底，以免損壞物件。

5. Do not strike the bottom of the cleaning cylinder with heavy objects to avoid damaging objects.

6、使用超聲波清洗設備清洗的工件不同，清洗液也要選擇不同的，清洗液如果選擇的不對，也會導致清洗效果不好。

6. Different cleaning fluids should be selected for different workpieces cleaned with ultrasonic cleaning equipment. If the cleaning fluid is not selected correctly, the cleaning effect will be poor.

7、清洗工作結束后，要及時倒出清洗液，并清潔儀器和清洗籃等配件。

7. After cleaning, the cleaning solution shall be poured out in time, and the instrument, cleaning basket and other accessories shall be cleaned.

8、全自動超聲波清洗機清洗工作結束后，要及時關閉電源。

8. After the cleaning work of the full-automatic ultrasonic cleaning machine is completed, the power supply shall be turned off in time.

以上就是問題解答的相關內容了，希望能夠幫助到大家，如對這一問題還存在任何疑問，都歡迎關注我們網站www.zjfsmy.com并咨詢我們的工作人員，將竭誠為您服務。

The above is the relevant content of the question answer. I hope it can help you. If you have any questions about this problem, you are welcome to follow our website and consult our staff. We will serve you wholeheartedly.